• 458 242 Miramar Ceiling Fan Owner’s Manual Miramar Ventilador de Techo de 1,52 Manual del Propietario. • Miramar por Hampton Bay ®. • 60” Miramar Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules.1 458-242 UL Model No. • Safety Rules - Read and Save These Instructions To reduce the risk of electric shock, insure electricity has been turned off After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning.
I swear under oath that the information I provide in this Petition is true and correct. My name is: First. ☒I am the Petitioner, and I am asking the court for an Occupational Driver's License (ODL). ☒I ask the Clerk to mail a certified copy of this Petition to The Texas Department of Public Safety. ☒I ask the Court to. Judgment of Acquittal by Jury or Court Renuncia Al Derecho De Interprete Certificado Para Declaracion Trial Court's Certification of Defendant's Rights of Appeal Waver of Attorney and Order for Pro Se Reorientation. Election of judge/jury to Assess Punishment Occupational License Case Information Sheet. Petition for occupational drivers license bexar county elections.
This Pin was discovered by Laural Home. Discover (and save) your own Pins on Pinterest.
Upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding All wiring must be in accordance with the National Electrical Code conductor on one side of the outlet box and ungrounded conductor on the. • Unpacking Your Fan Unpack your fan and check the contents.
You should have the following items: Set of blades (5) Fan motor assembly Blade Attachment Hardware (16 Screws with Fiber Washers) Canopy assembly Set of blade arms (5) Ball/downrod assembly Top glass housing Electrical Hardware Decorative top coupling cover. • Installing Your Fan Tools Required Figures 1~3 are examples of different ways to heavy duty fan brace as shown in Figure 2 mount the outlet box. (available at any Home Depot store). Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Provide Strong Support Mounting Options Recessed. • Installing the Decorative Installing the Downrod WARNING FAILURE TO PROPERLY INSTALL COTTER Scroll Assembly PIN AS NOTED IN STEP 5 COULD RESULT IN Remove the decorative canopy bottom cover FAN LOOSENING AND POSSIBLY FALLING. From the canopy by turning the cover counter For packaging purpose, the decorative scroll is clockwise.
• Attaching the Fan Motor Motor Wires Ball/Downrod Assembly Assembly Ceiling Canopy Remove the set screws, clevis pins and cotter Canopy Cover pins from the decorative scroll assembly, place the decorative scroll in the top plate of Upper Decorative motor assembly, align the screw holes at the Coupling Cover bottom of decorative scroll with holes in the Cotter Pins. • Installing Fan to the UL Listed Electrical Box Outlet Box Posts in the WARNING 120V Outlet Box Wires Ceiling TO REDUCE THE RISK OF FIRE, ELECTRIC Safety Cable SHOCK OTHER PERSONAL INJURY. Mounting MOUNT FAN ONLY TO AN OUTLET BOX OR Bracket Ceiling SUPPORTING SYSTEM MARKED ACCEPTABLE. • Making the Electrical WARNING SUPPLY CIRCUIT CHECK TO SEE THAT ALL CONNECTIONS ARE Connections TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS.
Ground EXCEPT FOR THE GROUND WIRE. REMEMBER to disconnect the power. Conductor WARNING If you feel you do not have enough electrical Outlet Box. • Finishing the Fan Outlet Box Installation Ceiling E12/15W Mounting Bulbs Bracket Tuck connections neatly into ceiling outlet Screw box.
Canopy Slide the canopy up to mounting bracket and Top Plate place the key hole on the canopy over the Screw screw on the mounting bracket, turn canopy Motor Housing until it locks in place at the narrow section of. • Attaching the Fan Blades Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of Attach blades to blade arms using three screws one of the blades. Measure from a point on the with fiber washers. • Installing the Light Kit CAUTION Raise the glass shade up against the light plate, BEFORE STARTING INSTALLATION, DISCON- place looped end of the safety cable over the NECT THE POWER BY TURNING OFF THE hook located on the light plate. Install the glass CIRCUIT BREAKER OR REMOVING THE FUSE shade onto the light plate with 4 screws AT FUSE BOX.